Talkback for article: 239, July2002

Hardware watchdog and shutdown button

Back to: http://cgi.linuxfocus.org/English/July2002/article239.shtml

From: Greg Pratt <gpratt3151(at)yahoo.com> [ date: 2002-07-04 ]
Once again, thanks for a great article! Interfacing external hardware to
Linux systems is an important topic and you've done a great job starting
from the basics and building up from there.
From: Alain Gauthier <AlGauRythme(at)yahoo.com> [ date: 2002-07-08 ]
We need good articles like yours, especially in hardware. You do a great
job. Congradulations and keep on the good work.
From: William Hathaway <william(at)melug-central.org> [ date: 2002-07-08 ]
Very good article.

However you noted only in passing a realworld application for this circuit. That is rebooting a hung computer that controls hardware is in an inaccessible place such as on the top of a mountain.



From: colyli <colyli(at)263.net> [ date: 2002-08-03 ]
This watchdog maybe can resolve Linux SMP auto powerdoen problem. When we try to type "halt -p" to shutdown SMP Linux system, the machine often failure for powerdown. If this watchdog can set a timer after we shutdown sytem, and act hardware to powerdown when timer expired, we can implement system auto powerdown!

great designing!
From: Freak [ date: 2002-09-18 ]
Great article...(on of the best i've read in the last month)

one question left: do you think it is right, that the RTS Voltage goes to the Reset Pin(4) of the NE555 insted of the Control-Votlage Pin(5), like in your drawing??
May be, i am fault, but i don't understand, why the NE555 schould be under reset all the time...
From: guido [ date: 2002-09-18 ]
HI "Freak",
no the NE555 schould not be under reset. That's why it has pin 4 connected
to supply voltage. Reset connected to logical "1" means reset off for the
NE555.

From: Freak [ date: 2002-09-18 ]
ok, thank you very much for your reply, i will try to build this circuit soon...
From: guido [ date: 2002-12-29 ]
There is a new and updated design available (version 0.4):
http://www.linuxfocus.org/common/src/article239/
From: atrak <watchdog(at)compot.ru> [ date: 2003-02-10 ]
А это наш watchdog
http://team.mit8.ru/projects/watchdog/index.php

From: Bhavesh Gudhka <gudhkabhavesh(at)yahoo.com> [ date: 2004-03-04 ]
I am looking for a circuit that can power off computer after halt. Is it posible with your circuit?

please suggest if any customization is required.


From: Guido Socher [ date: 2004-07-29 ]
Kurt Schlager has some variants of this watchdog on
his homepage:
http://www.das.cc/subdomains/kurt/watchdog/index.php
You can find there also a driver for Windows.
The site is in German.
From: flavio vasconi <flaviova(at)tin.it> [ date: 2004-12-31 ]
hi Guido, thanks for the great job you did.
By the way there is a small problem: if the application sending the pulses to DTR dies and the DTR remain permanently on, the wachdog does not detect it. A solution is to drive with this signal the reset 4. If you are interested i can send the diagram to you.
Thanks flavio
From: james last <sdf(at)aol.spam> [ date: 2005-02-09 ]
Hi,
great watchdog !!!!!!!!
Exactly what I was looking for .. Thanks you very very much !!
bye

From: hygy <hygy(at)freemail.hu> [ date: 2005-10-06 ]
So is the DTR remain permanently bug resolved?
From: hygy <hygy(at)freemail.hu> [ date: 2005-10-08 ]
Hi!

So the solution of the DTR stay on high level when crashed is:
<pre>
10uF
DTR --------||-----------R3 (3k3)-----
| |
LED 2k6 ohm
| |
| |
1k ohm |
| |
GND GND

</pre>

I put a led to see the signals comming from serial port. (I try this on a test board with 12V)
Now I connect it to serial and check it there too.

15 talkbacks in English
Other talkbacks:   Italiano Francais




Due to the increased amount of web spam we have deciced to removed the talkback posting possibility. You can read old talkbacks but you can no longer post new ones.

Back to http://cgi.linuxfocus.org/English/July2002/article239.shtml

Please contact webmaster(at)linuxfocus.org if you have any questions with regards to this talkback

lftalkback version 3.10